RED HAT 6.0 and SCSI ???

[noah at concord.org (Noah Fields)]

Brad,

There is a thread over at comp.os.linux.setup about the 2940UW card and RH
6 (note that everyone sais 5.2 works fine, but 6 causes trouble...) So at
least it seams that you are not alone.

I could not find articles at RH knowlege base though. (they had some
general info on trouble shooting the 2940's but nothing specific to RH
6.0... )




----- snip -----

>Author:	 	Jeffery Jones <jeffery_jones at SPAMFILTERmtlusa.com>
>Date:	 	1999/05/07

>I have a 2940UW, Toshiba 12x cdrom, and Ricoh cd writer. I found a
>small workaround but, like you would like to find out what's going on
>with this. After many tries with RH6, this is what I found:
>
>With both drives connected the installation hangs at scanning the scsi
>bus after prompting for the RH cdrom. If I remove one of the drives it
>works fine. I performed the whole installation with only one drive
>connected. After everything was configured and installed, I
>reconnected the second drive (Ricoh). Errors again on bootup. So I
>removed the Ricoh again and compiled a 2.2.7 kernel and adjusted the
>scsi timeout settings from "5" to "15". This seems to have done the
>trick. Now everything seems to be working fine although there is a
>slightly longer delay when the scsi chain gets probed on bootup now.
>
>Hope this helps for now.
>
>Regards,
>Jeff

Posted & courtesy emailed


On 6 May 1999 20:53:23 GMT, kchittur at nospam.che.uah.edu wrote:

>Brian Powers <bsp at falcon.cc.ukans.edu> wrote:
>> I'm having some serious problems installing RedHat 6.0 on my 4gb hard
>> drive attached to my Adaptec 2940UW.  I have no IDE drives in the
>> system, only an IBM 4gb ultrawide on the 2940's UW bus, and I have a 4gb
>> Seagate, a 4x NEC cdrom, and a Ricoh CDRW on the slower SCSI-2 bus.
>
>> My problem is that the installation hangs every time that it accesses
>> the SCSI controller.  It hangs when I autoprobe it, and even when I run
>> it in expert mode.  It detects the first 2 hard drives, and then it
>> gives me a message something to the effect of "Probably an unrecovereble
>> device hang" or something like that.
>
>I have the same problem.  I had a system running _almost_ fine with
>RH 5.0 - I tried to install RH 5.2 - got "scsi timeout error" - something
>like that - the problem WAS with Adaptec SCSI - RH 6.0?  same problem -
>
>So ... something got broken between RH 5.0 and RH 5.2 and RH 6.0 -
>
>It is frustrating.  I have been "evangelizing" Linux - I am still not
>"out of the ball game" - yet.  I want to get RH 6.0  and the kernel 2.2-
>series running -
>
>Why is RH 5.0 OK, RH 6.0 Not OK?


------------------------------------------------------------------------
___________________________________________________________________
Noah Fields :: noah at concord.org :: W 978.371.3480 :: C 617.699.4044
___________________________________________________________________
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: text/enriched
Size: 3536 bytes
Desc: not available
URL: <http://lists.blu.org/pipermail/discuss/attachments/19990508/2dac16b7/attachment.bin>